PocketWizard announces the PowerST4 Receiver for Elinchrome RX flash units" the latest accessory for the PocketWizard MiniTT1 and FlexTT5 Control TL radio system.
The PowerST4 Receiver enables remote power control of Elinchrom RX flashes with a camera-mounted PocketWizard MiniTT1 Transmitter or FlexTT5 Transciever. PocketWizard ControlTL technology allows you to control the flash power level using the cameras Flash Exposure Control (FEC). The PowerTracking feature automatically adjusts flash power to maintain the photographer-established level and thus proper exposure when the aperture and/or ISO is changed.
Slide the PocketWizard AC3 ZoneController into the shoe of the camera-mounted MiniTT1 or FlexTT5 and ST4 linked Elinchrom RX flashes can be controlled in three zones: A" B" and C in 1/3-stop increments over a six-stop range. The ST4 can also receive standard PocketWizard signals from a Plus" Plus II and MultiMAX transmitter. Set for Channel 1 at the factory" the ST4 can be easily set for any of the 20 ControlTL or 32 standard channels using the units' LEARN function or by USB connection with the PocketWizard Utility software. The PowerST4 draws its power directly from the Elinchrom RX flash remote control socket; theres no need to install or replace batteries.
Manual Power Control: When the PowerST4 is paired with either the MiniTT1 or FlexTT5 on camera" adjustment of flash power settings of the Elinchrom RX lights from the cameras position either with a Canon DSLRs Flash Exposure Compensation dial or the AC3 ZoneController for three zones of power control.
Zone Control with AC3: Use the AC3 ZoneController to control up to three zones of light with as many lights in each zone as you want. Use the A-B-C zone switch on the PowerST4 to assign the zone.
HyperSync: HyperSync allows achieving faster X-sync speeds" as fast as 1/8000 second*" with full power flash to better freeze action and use wide apertures in bright ambient-light conditions.
Programmable and Upgradeable: Use the PocketWizard Utility with the PowerST4s USB port to program the receiver to any PocketWizard channel and zone Use the utility to program initial power settings" modeling light settings and beeper settings The PowerST4 can be easily upgraded whenever updates and feature enhancements are available.
Uses All PocketWizard Channels: The PowerST4 can be programmed as needed with up to 20 ControlTL channels for Manual Power Control" or 32 standard channels for simple triggering. Channels can be configured with the <a >PocketWizard Utility</a>" or taught in the field with the Learn function.
Low-Profile Design: The PowerST4 is tiny and simply plugs into the remote socket on an Elinchrom RX flash and its power from the flash.
Length: 3.6 inches (9.2cm)
Width: 2.2 inches (5.5 cm)
Height: 1 inches (2.5 cm)
Length: 5.5 inches (13.97cm)
Width: 5.5 inches (13.97cm)
Height: 2 inches (5.08 cm)
Weight: 0.3 lbs. (0.14 kg)
Range - Performance / Basic Up to 500 meters (1600 feet)
Input-Output Connection : 3.5mm (1/8") stereo miniphone
jack, hot shoe
Triggering Speed: Up to 14.5 FPS
Voltage Present 43 volts, safe for use with all digital
and film cameras
Contact Time 102 milliseconds in normal operation
Power Two (2) AA (IEC: LR6) alkaline recommended
Battery Life Up to 50 hours (with alkaline batteries)
Mounting Hot shoe, lanyard/D-Ring loop, ¼-20 threaded
Camera/Flash Compatibilty Vivitar sync connector including 283 273
(Cords and Cable) 285 285HV3900
Usage (Cords and Cables) Remote Flash Sync
End Fittings (Cords and Cables) From Vivitar Male - To 1/8" Mono
Cable Length (ft) 1